Polk Audio Center Channel Speaker Kit Components to build one speaker New/Unused
This is a super kit, top quality components matched to give you a fantistic sound. You get the components to build One Center Channel Speaker, as a dual woofer design, you get the following.
(2) 5 1/4" Polk Audio Woofers (4 ohm) Shielded
(1) 1" Silk Dome Tweeter (8 ohm) Shielded
(1) Two Way Crossovers
Over All Specifications to expect
Power 20 to 150 Watts RMS Per Channel at 8 ohms
Impedance 8 ohms
Frequency response 40 Hz. to 20 kHz.
Efficiency 90 dB at 1 watt at 1 meter
Polk Audio Woofer Specifications
5.25" Polly Cone Shielded Woofer
Impedance 4 ohms (you wire in series to get you 8 ohm load)
Weight 3 pounds each
Revc - 3.4679 ohms
Fs - 56 Hz.
Zmax - 68 ohms
Qes - 0.4969
Qms - 9.2893
Qts - 4717
Le - 0.3484 mH (at 1 kHz.)
Vas - 22537.9746
BL - 0.1401 N/A
Sensitivity - 90 dB
Frequency response 40 Hz. to 7 kHz.
Tweeter Specifications
1" Silk Dome Soft Tweeter
8 ohms
Power 75 watts
Sensitivity - 89 dB
Frequency response 1.8 kHz. to 20 kHz.
Weight .5 pounds each
Misc. Information
If you buy two kits, you can use them to build a nice set of small towers, or a bookshelf speaker design. Then use the vertical layout for best performance.
Cabinet requirements are pretty basic, you should be fine keeping it around .5 cf. Ported works well for these woofers.
Wiring; the crossover to the speakers is very straight forward. We putting the woofers in series. Take the positive lead from the crossover and connect to the positive terminal of woofer #1. Then you will need a length of wire. This wire connects between the negative terminal on woofer #1 and goes to the positive terminal on woofer #2. Finally you run a lead from the Woofer Negative terminal of the crossover to the negative tab of Woofer #2.This completes wiring the woofers in series.
Hooking up the tweeter is easy, you run a lead from the crossovers Tweeter positive terminal to the positive tab of the tweeter. Then from the crossovers negative Tweeter terminal to the negative tab of the tweeter.
For best response use a tweeter centered design ( Horizontal Layout ), see picture below.
Polk Audio Center Channel Speaker Kit Components to build one speaker New/Unused
This is a super kit, top quality components matched to give you a fantistic sound. You get the components to build One Center Channel Speaker, as a dual woofer design, you get the following.
(2) 5 1/4" Polk Audio Woofers (4 ohm) Shielded
(1) 1" Silk Dome Tweeter (8 ohm) Shielded
(1) Two Way Crossovers
Over All Specifications to expect
Power 20 to 150 Watts RMS Per Channel at 8 ohms
Impedance 8 ohms
Frequency response 40 Hz. to 20 kHz.
Efficiency 90 dB at 1 watt at 1 meter
Polk Audio Woofer Specifications
5.25" Polly Cone Shielded Woofer
Impedance 4 ohms (you wire in series to get you 8 ohm load)
Weight 3 pounds each
Revc - 3.4679 ohms
Fs - 56 Hz.
Zmax - 68 ohms
Qes - 0.4969
Qms - 9.2893
Qts - 4717
Le - 0.3484 mH (at 1 kHz.)
Vas - 22537.9746
BL - 0.1401 N/A
Sensitivity - 90 dB
Frequency response 40 Hz. to 7 kHz.
Tweeter Specifications
1" Silk Dome Soft Tweeter
8 ohms
Power 75 watts
Sensitivity - 89 dB
Frequency response 1.8 kHz. to 20 kHz.
Weight .5 pounds each
Misc. Information
If you buy two kits, you can use them to build a nice set of small towers, or a bookshelf speaker design. Then use the vertical layout for best performance.
Cabinet requirements are pretty basic, you should be fine keeping it around .5 cf. Ported works well for these woofers.
Wiring; the crossover to the speakers is very straight forward. We putting the woofers in series. Take the positive lead from the crossover and connect to the positive terminal of woofer #1. Then you will need a length of wire. This wire connects between the negative terminal on woofer #1 and goes to the positive terminal on woofer #2. Finally you run a lead from the Woofer Negative terminal of the crossover to the negative tab of Woofer #2.This completes wiring the woofers in series.
Hooking up the tweeter is easy, you run a lead from the crossovers Tweeter positive terminal to the positive tab of the tweeter. Then from the crossovers negative Tweeter terminal to the negative tab of the tweeter.
For best response use a tweeter centered design ( Horizontal Layout ), see picture below.
Deutsch
Dansk
Español
Française
Italiano (IT)
Dutch
Norsk
Svenska
